Wednesday May 23, 2012 3:10 PM AEST

Atomic MPC > Features > Build > CPUs, Motherboards & RAM > Atomic guide to CPU lapping

Atomic guide to CPU lapping

« »

Once we were finished with the 400 grit, the next step up is the 800. Follow exactly the same steps with this as before, taping down and using only a small amount of water. You’ll know you’re finished with this grit once the deeper scratches left by the previous grit have mostly been rubbed away.

Moving from the 800, you can move up in steps of four hundred all the way to 2000, though we stopped at 1200 simply due to the fact that going that far isn’t worth the time spent. This will take you a while, so make sure you have the TV on, or some beer to drink (just not too much, it makes it…tricky). Once you’re finished with the 1200 grit, you should have something very flat, with only a few incredibly fine scratches.

To give an idea of just how flat this has made the CPU, here’s a side-on shot:

What will we do next?...

« »

Aliens: Colonial Marines in depth; Z-77 Motherboard round-up; strategy gaming special; Home Server tutorial. PLUS MUCH MORE - ON SALE NOW!

Ads by Google

20 Comments

iamthemaxx Jan 23, 2009 4:59 PM	George St, Sydney called. It want's to know if you have finished lapping as it's wearing away!
LordBug Jan 23, 2009 5:22 PM	WTF? BMP images? Slaaaaaack! :P
nesquick Jan 23, 2009 5:41 PM	lol 2-3degrees is not worth 4hours of my time not to mention for less you could probably buy a second fan for that TRUE and get the same result.
MedicineBaby Jan 23, 2009 6:07 PM	I have heard of CPU lapping but never actually seen any results from it before nor knew of how it was done, but thanks for the guide Justin. I might try it on a cheap chip before I do it on my main one though XD A question though Justin, what is the best drop in temperature you can get out of CPU lapping and what were your expectations when you first set out to lap the i7?
TheFrunj Jan 23, 2009 9:24 PM	LB: I'm sure you'll live :P MB: The best drop you'd expect is up to ten degrees, with very shonky heatsinks and CPUs. The TRUE is already extremely good, lapping lesser heatsinks will give better increases :)
scruffy1 Jan 23, 2009 10:58 PM	my only tip is using light machine oil instead of water to "wet" the surface otherwise : yup, that's how you do it nice guide
Xabbu Jan 24, 2009 5:05 AM	awesome guide mate :)
t8y Jan 26, 2009 6:57 PM	yep, did this about a month or two ago on my q6600 & TRUE120, plenty of youtube vids on the subject if you want to see it actually being done before you try it yourself.. i used an old mirror, and went 400-600-800-1200-1500. gave a good shine, and anything more is for e-peen lol oh; i got a drop in the range of 10*C (load went from 78 to 68 @ 3.6), my TRUE had a rough, uneven surface (badly machined, and as it turned out was slightly higher in centre and one edge) and my cpus IHS was slightly higher on the corners and one edge - as these parts started to show copper much earlier than the rest of the surface. recommended..
xtort Jan 27, 2009 8:18 AM	kerro is what we use at work for wet and dry paper has the added advantage of been non conductive. figuer eights are the best motion to use as the wear is even and can get it done a bit quicker. you can also use a marker to "blue" the surface that you are lapping and this will help you not to round the edges and stuff your cpu! it shouldnt take four hours maybe one or so good guide though if you have NFI I have done it and recomend it all the stuff is mass produced and only needs to be within the manufactures tolerances which could be anything up to .5mm out end to end
Jack Genders Jan 27, 2009 9:14 AM	Done this to my TRUE, not sure if I'd trust myself on the CPU though. Brave of you to give it ago, I can't magically pull the $$$ out of a new CPU if it goes wrong.
Jeruselem Jan 27, 2009 2:15 PM	Intel support folks must be cringing when they see this!
Hawkeye Jan 27, 2009 2:52 PM	Enthusiast: Oh, hi, is this Intel Support? Intel Support: Yes it is, how can I help you? E: Well, I lapped my CPU and - IS: DEAR MOTHER OF GOD, WHY?!?!?! E: Hello? Uh, is there anyone there?
nesquick Jan 27, 2009 6:20 PM	lol David, although I think it would be more like: Enthusiast: Oh, hi, is this Intel Support? Intel Support: Yes it is, how can I help you? E: Well, I lapped my CPU and - IS: uhh..... whats lapping? whats a cpu? is that the box thing? E: palm face pause Just forget it.
orcone Feb 2, 2009 3:06 PM	Why exactly are you using glass? That was never made clear. LOL GLASS CLEAR I AM COMEDY
osama_bin_athlon Feb 3, 2009 10:17 AM	why not just remove the IHS?
osama_bin_athlon Feb 3, 2009 10:19 AM	er, you use glass for a perfectly flat surface to work with/on ;P
marvin_aus Feb 9, 2009 3:01 PM	orcone, google on how a mirror or any form of flat glass is made. it's a pretty cool process
Kimmo Feb 12, 2009 2:00 AM	If you CBF faffing about with wet-and-dry, reasonable results can be obtained by scraping a fresh snap-blade across the surfaces in question...
Lale Feb 21, 2009 11:35 AM	The purpose of CPU lapping is just to make the surface flat. There might be a better way...use LIQUID METAL to fill the gap between heatsink and IHS coz liquid would be flowing to anywhere any gap. Check http://www.jecca.com.au/products/1096-010-001.htm
jack101 Apr 18, 2009 11:35 PM	Not worth the 2 degree drop for losing your warrenty

Comments have been disabled on this article.

Atomic Magazine

Issue: 137 | June, 2012

Atomic is a magazine aimed squarely at computer enthusiasts, gamers, and serious PC upgraders.

Every month we bring you the latest reviews of new technology and PC components, in depth features on everything from overclocking to console hacking, and gaming previews and interviews.

What's in this issue?